Construction and Debugging of Semi-Physical Closed Loop of Control System This article first established a component-level real-time model of a certain turboshaft engine, and then used this real-time model to form a closed-loop system on a mechanical hydraulic fuel conditioning system. This experiment was carried out on the 608 vortex-shaft engine semi-physical simulation test bench. The experimental setup is shown in Figure 2. The engine digital simulator is equipped with a real-time component-level model of a turboshaft engine. Based on the position of the load rod (given by the external potentiometer of the experimental device) and the fuel flow rate Gfu, the gas generator rotational speed N and the power turbine speed are calculated from the model. N. Compressor outlet static pressure P and N are sent to the control cabinet through the AD channel output rotation speed signal to drive motor 1 and motor 2, respectively; and the output pressure P electrical signal is converted into a pressure signal after electrical conversion, after the voltage divider The pressure is P' and it is sent to the fuel control system. The automatic fuel controller controls the N rotation speed to keep constant by G′ reflecting the oil-gas ratio. Because the numerical control system of the turboshaft engine is still under development, this experiment uses a hydraulic mechanical fuel conditioning system instead. This article first carried out the open-loop acceleration and deceleration test. After a preliminary assessment of the system work, the fuel flow rate at the starting point can be cut into the closed loop just by roughly the same amount. During the closed-loop experiment, a strong fuel oscillation was caused when the load lever was pushed, so that the system could not work normally. After analyzing the experimental results, the following methods were adopted: (1) The resistance of the fuel regulator was increased: the semi-physical simulation study of the intelligent fault-tolerance technology of the engine numerical control system reduced the magnification; (2) increased the interrupt timing procedure, and Simplify the real-time graphical interface, all curves and digital quantities are displayed in the simplest way, taking into account the interface is convenient and friendly. Finally solved the problem of fuel oscillation. It should be noted that the same oscillation phenomenon occurs when this set of systems is used together with the engine to perform a bench test, which is also solved by increasing the damping and reducing the amplification factor. The results of the semi-physical simulation experiment of the engine control system show that the semi-physical simulation results are consistent with the turret test of the turboshaft engine. The system can be used for intelligent fault-tolerance semi-physical simulation experiments of engine control systems. Epoxy resin is a kind of polymer material with high performance. It is a two-component system composed of epoxy group and amine group, which forms polymer compound by mixing and reaction. It has strong adhesive force, corrosion resistance, heat resistance, electrical insulation and mechanical strength, and is widely used in aviation, aerospace, automotive, construction, electronics, ships and other fields. Epoxy Resins,Crystal Clear Epoxy Resin,Hardener Epoxy Resin,Liquid Epoxy Resin Shanghai Shengduan Trading Co., Ltd. , https://www.sdcuringagent.com
The preparation process of epoxy resin is to mix epoxy resin monomer and amine Curing Agent in a certain proportion, and react at a certain temperature to form a polymer compound. Epoxy resins with different properties can be obtained by changing the type of monomer, the type and proportion of curing agent.
The advantage of epoxy resin is that its properties can be adjusted according to needs, and materials with high strength, high stiffness, high toughness, high temperature resistance, corrosion resistance and other characteristics can be prepared. Because of its excellent properties, epoxy resins are widely used in various fields. For example, in the aerospace field, epoxy resins are used in the manufacture of aircraft and rocket structural parts, composites, coatings and adhesives; In the automotive field, epoxy resins are used in the production of automobile body and engine parts; In the field of construction, epoxy resins are used in coatings, floors, waterproof materials and so on.
In addition, carbon fiber reinforced epoxy resin composites are also one of the most widely used epoxy resin products at present. Carbon fiber reinforced epoxy resin composites have the advantages of high strength, high modulus and low density, and are widely used in aviation, aerospace, automobile, sporting goods and other fields.
In general, epoxy resin is a high-performance material with a wide range of application prospects, and its properties can be adjusted according to needs, and it is widely used in various fields.